Setting dashboard gauges and notifications
Menu location: Maintenance menu, Dashboard Setup, Dashboard Maintenance
The dashboard offers visual trending tools that measure key performance
in your revenue cycle. The tools include up-to-the-minute gauges on both
the Claim tab and the Eligibility
tab. The dashboard also alerts contacts to specified product events.
Use dashboard maintenance to configure trending gauges and define event alerts. To set up contacts, refer to Setting up notification contacts.
Gauge settings
There are four gauges presented at the top of each Operations Dashboard tab, and they correspond to a Gauge field listing:
| Dashboard | Gauge setting | Description |
|---|---|---|
| Claim | Unreleased |
Total number of claims in the database that have not yet been released to the payer. (Unreleased Count gauge) |
| Claim | Unreleased Dollar Amount | Total value of claims in the database that have not yet been released to the payer. (Unreleased Dollars gauge) |
| Claim | Held Claim Count | Total number of unreleased claims held by a hold code. (Held Count gauge) |
| Claim | Held Dollar Amount | Total value of unreleased claims held by a hold code. (Held Dollars gauge) |
| Eligibility | Unreleased Pending Eligibility Count | Total number of unreleased claims for which a response to a request has not yet been received. |
| Eligibility | Unreleased Pending Eligibility Amount | Total value of unreleased claims for which a response to a request has not yet been received. |
| Eligibility | Released |
Total number of released claims for which a response to a request has not yet been received. |
| Eligibility | Released Pending Eligibility Amount | Total value of released claims for which a response to a request has not yet been received. |
Each gauge contains a tri-colored range used to measure results achieved against defined performance objectives:
- Red (high) represents a warning range that dangerously exceeds a safe level of performance.
- Green (low) represents a positive range that falls below minimum objectives.
- Yellow (moderate) represents a range that exists between high and low values entered.
To define performance objectives, you need to specify the high and low levels for each gauge. Moderate values are automatically calculated by subtracting .01 from the high and adding .01 to the low. If no values are set, gauge segments will be equally divided based on your site's database totals. For example, if your site has 30,000 unreleased claims, the Unreleased Count low will be set to 10,000 and the high to 20,000. This will result in an even distribution of 10,000 counts per segment.
The default values are "66.00" for High and "33.00" for Low. Custom values should be set as soon as possible.
Follow these steps to set values:
- Select the Gauge you want to set.
- In the High >= field, enter maximum acceptable value. For example, if your objective is to stay below 2500 unreleased claims, enter 2500 in this field for the Held Claim Count. All counts greater than and equal to this value will be shown as red for high.
- In the Low <= field, enter the highest value that still falls within objectives. For example, if 250 unreleased claims is an acceptable minimum standard, enter 250 in this field. All counts less than and equal to this value will be shown as green for low. All counts between the Low and High values show up as yellow for moderate.
- Repeat for each remaining gauge, and click OK.
Notification settings
Notification services allow you to define specific operational conditions that notify users of events that occur within the system. Events can be based on achieving or missing thresholds defined (e.g., notify the Billing Lead if the Claim Error Rate is above 15% for any claim file). They can also be used to notify or escalate awareness of events that have completed or have not yet been started in the system. (e.g., completion of release process, lack of claims to submit, etc.).
Threshold options for configurable events vary. For Held Claims Count, Held Claims Value, and No Claims
Bridged/Released by Specified Time; you can specify the frequency and time of alerts. For
Claim Aging, Error Rate After Bridging
Bridging is the process that takes your information files from your HIS and then creates claims in this billing system for you to work. Bridging is also called “submission.” Claims, and Job Failure, alerts are sent as soon as
the events are triggered in the system.
If you select the Job Failure (Any) item as the event threshold, the following job failures will cause an alert: ASC, Auto List, Bridge, Claim Extract, DEChangePassword, DECheckEdits, DECheckEligibility, DECheckStatus, DepExtract, DESendClaims, EPD Install, ExportClaims, Import 277, Import 835, Import Aii
Advanced Inquiry Interface (Aii) is the program that queries Medicare for early adjudication results. Largely replaced by Medicare Direct Entry (MDE)., Import Claims, PaperClaims277, PaperClaimsEOB, PaperClaims, PREMIS Import, Product Import, RebillClaims, Recalc Remits, Release, Report, SecondaryBillClaims, SpinOffClaims.
Follow these steps to add an event:
- Select Add New Notification Event from Notification Events.
- In Event Name, enter a descriptive name for the new event. Special characters are allowed.
- Select an event threshold from Notify When. Enter the requested threshold, if needed based on the event parameters.
- If configurable for the event, select the notification Days and Hour.
- In the Notification Message Body field, type a message that you would like to have sent to recipients at each occurrence of the event.
- Select Notification Contacts (set up contacts in Notification Contacts). Select names from All Contacts, and use the arrow button to move the names to This Event list.
- Click Add.
- Repeat for additional events, or click OK to save work.
Follow these steps to modify an event:
- Select the Notification Event you want to modify.
- Make necessary changes in appropriate fields, and click Update.
- Repeat for additional events, or click OK to save work.
Follow these steps to remove an event:
- From the Notification Event you want to remove.
- Click Remove.
- Repeat for additional events, or click OK to save work.